汽車電機爪極液態模鍛模具及工藝設計

機械論文編號:JX851  論文字?jǐn)?shù):13366.頁數:34   附CAD圖

 目 錄
摘   要 I
Abstract II
目 錄 III
第一章  緒論 1
1.1 液態模鍛簡介 1
1.2 液態模鍛的國內外現狀與發展趨勢 2
1.2.1 液態模鍛國外現狀 2
1.2.2 液態模鍛國內現狀 4
1.2.3 液態模鍛的發展趨勢 5
第二章  液態模鍛工藝及特點 7
2.1 液態模鍛工藝的分類 7
2.2 液態模鍛工藝特點及適用范圍 9
 2.2.1 液態模鍛工藝特點 9
2.2.2 液態模鍛的適用范圍 9
2.3 液態模鍛工藝的優點及比較 10
2.3.1 液態模鍛工藝的優點 10
2.3.2 選用液態模鍛加工汽車爪極的優點 12
第三章  汽車爪極液態模鍛工藝參數分析 14
3.1 汽車爪極零件 14
3.2 液態模鍛工藝參數分析 14
3.2.1 壓力大小 15
3.2.2 加壓開始時間 16
3.2.3 加壓速度 16
 3.2.4保壓時間 16
 3.2.5 金屬澆注溫度 16
 3.2.6 模具溫度 17
 3.2.7 涂料 18
第四章  汽車爪極液態模鍛模具設計 19
4.1 汽車爪極液態模鍛模具設計總體方案確定 19
4.1.1 液鍛件的形狀分析 19
4.1.2 液鍛方式的選擇 19
4.2 汽車爪極液態模鍛模具參數計算 19
4.2.1 汽車爪極的投影面積、體積及壓力中心計算 19
4.2.2 汽車爪極液態模鍛過程的總壓下量計算 20
4.2.3 汽車爪極液鍛力計算 20
4.2.4 脫模斜度 20
4.2.5 脫模力計算 21
4.3 汽車爪極液態模鍛模具零件設計 21
4.3.1 凹模 21
4.3.2 凸模 24
4.4 汽車爪極液態模鍛模具裝配圖的設計繪制 25
第五章  總結 27
參考文獻 28
致  謝 30

摘   要
 汽車電機爪極是汽車電機的關鍵部件, 一般采用傳統的鑄造工藝，工步繁多，性能較低，研究新型工藝進行加工，降低成本，對提高質量有著重要的意義。
 本文對汽車電機爪極采用液態模鍛工藝。經過對該零件工藝分析和計算，確定合理的液態模鍛工藝方案，設計出液態模鍛工序的整套模具，使用UG,AutoCAD等繪圖軟件繪制模具零件圖和裝配圖。
 通過對汽車爪極模具設計，鞏固和深化了所學知識，取得了比較滿意的效果，達到了預期的設計意圖。

關鍵詞：汽車爪極  液態模鍛  CAD　模具零件圖　裝配

Squeeze Casting Design of Automotive Longitudinal Beam

Abstract
 Automotive Claw mold design and manufacturing is the critical part of the automotive industry, and the traditional casting process owns complex mold and various steps. research new technology for processing, reduce costs and improve product quality.
 In this paper, automotive Claw using squeeze casting process. After analysis of the components and calculation process to determine a reasonable scheme of squeeze casting process. design a complete set of mold of squeeze casting craftwork and use UGAutoCAD and other graphics software to draw maps and mold parts,
 By designing the automotive ,the author has strengthened and deepened those learned knowledge and acquired very pleasant result, also achieved the expected intention of designing.
Key  words:  Automotive claw；Squeeze casting; CAD ;Mold part drawing; Assembly