C6140普通車床主軸箱傳動設計

論文編號:JX1645  論文字?jǐn)?shù):7570.頁數:25 附任務書，開題報告，外文翻譯,CAD圖

C6140普通車床主軸箱傳動設計
 摘要：本文用簡明的語言有側重的介紹了普通機床中C6140主軸的設計過程，先通過研究背景及選題意義的介紹，來引出本設計的意義。然后分別從參數擬定、傳動設計、傳動件的估算和驗算、各部件結構設計和主軸組件的驗算5個部分來進行設計的。以齒輪、帶輪、皮帶輪、軸承、箱體等的參數設計為重點。
 
 關鍵詞：齒輪；結構設計；箱體
 
C6140 lathe headstock Transmission Design

Abstract: This article has focused on using plain language introduction to the general machine tools in the design process of C6140 spindle, first by studying the background and significance of the topic's introduction, to elicit the significance of this design. And then were prepared from the parameters, transmission design, estimation and checking transmission parts, components structural design and checking 5 spindle components for the design part. The gears, belts, pulleys, bearings, cabinet and other key design parameters.

Keyword: Gear; structural design; box
    
 目錄
1.車床參數的擬定- --------------------------------------------------2
 1.1概述--------------------------------------------------------------2
 1.2參數的擬定--------------------------------------------------------2
2.運動設計- ----------------------------------------------------------3
 2.1傳動結構式、結構網的選擇確定---------------------------------------3
 2.1.1傳動組及各傳動組中傳動副的數目----------------------------------3
 2.1.2傳動系統擴大順序的安排 -----------------------------------------3
 2.1.3繪制結構網------------------------------------------------------4
 2.1.4傳動組的變速范圍的極限值----------------------------------------4
 2.1.5最大擴大組的選擇------------------------------------------------5
 2.2轉速圖的擬定------------------------------------------------------5
 2.2.1主電機的選定----------------------------------------------------5
2.3齒輪齒數的確定及傳動系統圖的繪制----------------------------------5
2.3.1齒輪齒數的確定的要求--------------------------------------------5
 2.3.2變速傳動組中齒輪齒數的確定--------------------------------------6
3.強度計算和結構草圖設計-- ---------------------------------------9
 3.1確定計算轉速------------------------------------------------------9
 3.1.1主軸的計算轉速--------------------------------------------------9
 3.1.2中間傳動件的計算轉速--------------------------------------------9
 3.1.3齒輪的計算轉速-------------------------------------------------10
 3.2傳動軸的估算和驗算-----------------------------------------------10
 3.2.1傳動軸直徑的估算-----------------------------------------------10
 3.2.2主軸的設計與計算-----------------------------------------------11
 3.2.3主軸材料與熱處理-----------------------------------------------12
 3.3齒輪模數的估算和計算---------------------------------------------14
 3.3.1齒輪模數的估算-------------------------------------------------14
 3.3.2齒輪模數的驗算-------------------------------------------------17
 3.4軸承的選擇與校核-------------------------------------------------19
 3.4.1一般傳動軸上的軸承選擇-----------------------------------------19
 3.4.2主軸軸承的類型-------------------------------------------------20
 3.4.3軸承間隙調整---------------------------------------------------20
 3.4.4軸承的校核-----------------------------------------------------21
 3.5摩擦離合器的選擇與驗算-------------------------------------------22
 3.5.1按扭矩選擇-----------------------------------------------------22
 3.5.2外摩擦片的內徑d- ----------------------------------------------22
總結----------------------------------------------------------------- 23
參考文獻- -----------------------------------------------------------24
致謝----------------------------------------------------------------- 25