汽車剎車主缸密封檢測臺開發

論文編號:JX1551  論文字?jǐn)?shù):11149.頁數:43 附任務書，開題報告，文獻綜述，外文翻譯

摘  要

 本次畢業設計開發了剎車主缸密封檢測臺，用于檢測剎車系統中主缸的密封性能。完成了檢測臺系統整體結構的設計，確定了硬件系統的組成和零部件。本課題中的機械部分以氣動結構為核心，利用觸摸屏與PLC作為中央處理核心。
 根據安裝好的設備以及控制流程圖提供的總體設計思路編寫了PLC程序，用于控制各執行元件，實現了對主缸的高壓（主缸內兩腔分別0.7MPa和0.5MPa），低壓（140KPa），以及端面密封（0.5MPa）的檢測。本課題開發的剎車主缸密封檢測平臺，可以實現對汽車剎車系統中主缸的密封性能檢測，多次測試表明本系統精度高、處理速度較快，達到了實時檢測的要求。
 
關鍵詞：密封檢測； PLC；觸摸屏

Abstract
 In this graduation design, I participate in a project to exploit Master Brake Cylinder Test-bed, which was used to detect seal capability of Master Brake Cylinder in brake system of automobile. We finished construction of the whole system design, and defined structure and spare parts of the hardware system. In this project we built pneumatic structure as the core of machinery parts, and touch screen compose PLC(Programmable Logic Controller) as the central processor.

 Under this fixed devices and flow chart which direct us the whole design scheme, we could program to control the other actuators. At last we should debugging the whole system, detect the Master Brake Cylinder in high pressure(each cavity inside the Master Brake Cylinder is 0.5MPa and 0.7MPa), low pressure(140KPa) and end sealing capability(0.5MPa).This Master Brake Cylinder Test-bed can detect seal capability of Master Brake Cylinder in brake system of automobile, times of tests showed the high accuracy and hyper processing speed of this system, reached the requirement of immediate detection.

Key words:  Sealing capability detection ；PLC ；Touch screen

目  錄
摘要……………………………………………………………………………………I
Abstract…………………………………………………………………………………II
目錄………………………………………………………………………………………III
1 前言…………………………………………………………………………………1
2 總體設計方案………………………………………………………………………3
 2.1 硬件系統………………………………………………………………………………… 4
 2.2 軟件系統………………………………………………………………………………… 5
3 檢測臺構成…………………………………………………………………………6
   3.1 機械部分………………………………………………………………………………… 6
   3.2 氣動結構………………………………………………………………………………… 6
   3.3 電氣系統…………………………………………………………………………………13
       3.3.1 OMRON CP1H XA40DR-A……………………………………………………………13
       3.3.2 RS-232C通訊模塊   OMRON CP1W-CIF01………………………………………15
       3.3.3觸摸屏 MT6056i…………………………………………………………………17
       3.3.4氣壓傳感器 CS1-G………………………………………………………………18
4 PLC編程………………………………………………………………………… 19
   4.1 PLC控制閥動作的氣路編程…………………………………………………………  19
   4.2控制流程圖……………………………………………………………………………  19
   4.3 編程語言………………………………………………………………………………  21
   4.4 編程環境CX-Programmer 7.3………………………………………………………… 22
5 系統的調試………………………………………………………………………23
   5.1 氣路的調試…………………………………………………………………………… 23
   5.2 程序的調試…………………………………………………………………………… 23
   5.3 系統的改進方向……………………………………………………………………… 23
6 總結………………………………………………………………………………25
致謝…………………………………………………………………………………26
參考文獻…………………………………………………………………………………27