3000ta有機硅涂層膠生產企業的總平面圖設計

材料科學論文編號:CL081  論文字數:10199,頁數:25

目  錄
中文摘要 I
英文摘要 II
目錄 III
1. 緒論 1
 1.1 有機硅涂層膠的概述...........................................1
 1.2 本課題的提出.................................................2
2.基本概況...........................................................2
 2.1 項目產品、物化性質及用途.....................................3
 2.1.1  有機硅涂層膠簡介......................................3
 2. 2 工藝技術方案................................................3
           2.2.1生產工藝及物料平衡................... 3
           2.2.2 原輔料性質及用量.................... 3
           2.2.3主要設備................................4
           2.2.4主要建筑..............................4
           2.2.5全廠定員...............................5
      2.3 投資概算...........................5
      2.4 建設選址、用地與相關規劃......... ............................6
      2.5 資源利用和能源耗用分析......... .........6
      2.6 生態環境影響分析......... ............6
3. 設計部分 8
 3.1 廠區平面圖 8
 3.1.1 總體布局 10
 3.1.2 布置理念 11
 3.1.3 各區域集中布置........ ........ ........ ...............11
 3.2 行政中心和研發中心的設計 12
 3.3倉庫的設計.................................................. 13
  3.4生產區的設計................................................15
  3.5甲類灌區的設計..............................................16
  3.6 污水處理區設計.............................................16
  3.7 消防設計...................................................16
      3.7.1 設計依據.............................................16
      3.7.2 事故發生可能性及危險性分析...........................16
      3.7.3 燃燒爆炸的原因.......................................17
      3.7.4 消防安全措施.........................................17
                3.7.5 消防系統........................................18
          4．總結與展望.................................................19
致謝................................................................20
參考文獻............................................................21

摘 要：有機硅涂層膠具有良好的阻燃性和熱穩定性，他可以增強涂層強度、彈性，也可降低摩擦系數。有機硅涂層膠具有較好的滲透性、熱穩定性好、表面張力低、平滑性佳、橡膠彈性和通氣透濕性優良、對皮膚無刺激等特點,所以它是一種應用廣泛,前景光明的紡織助劑。自從20世紀70年代以來，有機硅涂層膠在國內外迅速發展，產品性能也越來越穩定，工藝路線日趨完善，所以我們根據目前有機硅涂層膠工藝，進行此產品的工廠設計，而我所負責的是3000t/a有機硅涂層膠生產的總平面圖設計。設計的內容包括行政和研發中心，生產車間的設計，倉庫的設計，消防中心的設計及一些輔助設備的設計，設計采用的依據GB 50187-93和GB50016-2006.
關鍵詞：有機硅涂層膠、總平面圖、設計。

Abstract: Silicone coating adhesive has good resistance and thermal stability, he can enhance strength, elasticity, coating can reduce the friction coefficient. Silicone coating adhesive has good permeability, good thermal stability, low, smooth the surface tension, rubber permeability good elasticity and ventilation, no stimulation to the skin etc, so it is a kind of wide application prospects of light, the textile auxiliaries. Since l970s, silicone coating adhesive products at home and abroad and rapid development, more and more stable performance, technology route has been improved, so we according to the current organic silicon coated adhesive products factory, the design, but I was responsible for the organic silicon introduces/a total floor coating adhesive production design.
Keywords：Silicone coating adhesive；general plan；design.